dc.contributor.author | ÖZEK, Cebeli; ÜNAL, Engin | |
dc.date.accessioned | 2019-01-16T12:12:16Z | |
dc.date.available | 2019-01-16T12:12:16Z | |
dc.date.issued | 2018 | |
dc.identifier.citation | | en_US |
dc.identifier.uri | http://fenbildergi.aku.edu.tr/wp-content/uploads/2018/12/015904-1149-1157.pdf | |
dc.identifier.uri | http://hdl.handle.net/11630/5129 | |
dc.description | In order to shape of spherical bottom cups in angular deep drawing die, the effect of surface flow angle
of the sheet (SFAS), the blank holder force (BHF) and the limit drawing ratio (β) at different radii of the
die and the thickness of the cup on the thickness changes were investigated by using DKP37 material.
Surface slope where the sheet flows angles have θ=0°, θ=5°, θ=10°, θ=15° and the punch were machined
of Rz=25 mm radius. The punch diameter is 47,8 mm, the die diameter is 50 mm and the die-punch gap
is 0,9 mm. In this study, when the surface flow angle of the sheet was θ=0° and θ=15°, limit drawing
ratio was obtained as β=1,87 and β=2,42. Thus, the lowest thickness change in the cups were obtained
of 0,723; 0,765; 0,819 and 0,868 mm for θ=0°, θ=5°, θ=10° and θ=15°, respectively. As a result of the
research, it has been determined that larger limit drawing ratios (β) are obtained in the new spherical
deep drawing die which is manufactured in different angles and unchanged punch radius | en_US |
dc.description.abstract | Küre tabanlı kapların açılı çekme kalıplarında şekillendirilmesi için DKP37 malzemesi kullanılarak, sacın
aktığı yüzey açısı (SAYA), baskı plaka kuvveti (BPK) ve matris farklı yarıçaplarında limit çekme oranı (β)
ve kap et kalınlık değişimleri üzerindeki etkileri araştırılmıştır. Sacın aktığı yüzey eğimi θ=0°, θ=5°, θ=10°,
θ=15° açılarda, zımba ucu Rz=25 mm radyüs ile imal edilmiştir. Zımba çapı 47,8 mm, matris çapı 50 mm
ve matris aralığı 0,9 mm dir. Bu çalışmada, sacın aktığı yüzey açısı (SAYA), θ=0°’de β=1,87 iken, θ=15° de β=2,42 oranı yakalanmış, böylece kaptaki, en düşük kalınlık değişimi θ=0°, θ=5°, θ=10°, ve θ=15° için
sırasıyla 0,723; 0,765; 0,819 ve 0,868 mm olarak elde edilmiştir. Araştırma sonucunda değişik açılarda
ve sabit zımba yarıçapında imal edilen yeni tip küresel derin çekme kalıbında, açısız kalıplara göre daha
büyük çekme oranlarının (β) elde edildiği belirlenmiştir. | en_US |
dc.language.iso | tur | en_US |
dc.identifier.doi | 10.5578/fmbd.67820 | en_US |
dc.rights | info:eu-repo/semantics/openAccess | en_US |
dc.subject | Küresel kaplar; Açılı derin çekme; Baskı plaka açısı; Limit çekme oranı. | en_US |
dc.title | Küresel Tabanlı Kapların Şekillendirilmesinde Sacın Aktığı Yüzey Açısının Limit Çekme Oranı ve Et Kalınlığı Değişimi Üzerindeki Etkisi | en_US |
dc.title.alternative | The Effect of Surface Angle of Flowing Sheet on The Limit Drawing Ratio and The Wall Thickness Change in Drawing of Spherical Bottom Cups | en_US |
dc.type | article | en_US |
dc.relation.journal | Fen ve Mühendislik Bilimleri Dergisi | en_US |
dc.department | Afyon Kocatepe Üniversitesi | en_US |
dc.identifier.volume | 18 | en_US |
dc.identifier.startpage | 1149 | en_US |
dc.identifier.endpage | 1157 | en_US |
dc.identifier.issue | 3 | en_US |
dc.relation.publicationcategory | Makale - Ulusal Hakemli Dergi - Kurum Yayını | en_US |